How to Make a Curtain with Lace Inserts

Curtain with Lace Inserts

From plain to chic in a jiffy, add sophistication to a simple curtain in very few steps. All you need is some fabric, lace strips and a ruler. A few straight seams later and voilà!

Curtain with Lace Inserts

Curtain with Lace Inserts

Supplies

  • Fabric for curtain (see step 1 for yardage)
  • Lace trim (see step 2 for yardage)
  • Scissors
  • Thread
  • Ruler

Step 1) Measure your window and determine how large you want your finished curtain to be.

Most curtain panels are 1-1/2  to 2 times the width of the window; this allows for a bit of fullness. Add 2″ to the desired final width to determine how wide your fabric needs to be.

Decide how long you want your curtain to be. Add 4-1/2″ to the length for a rod casing and another 4-1/2″ for a hem allowance.

Step 2) Measure the depth of the lace and adjust the length of the curtain panel.

For each lace strip you need enough to span across your curtain’s width plus 2″.

To make room for the lace strips, first decide how many lace strips you want to add. Record how deep the lace is. For each strip of lace, subtract 1-1/2″ from its depth. Subtract that number from the curtain’s length to make room for each lace strip. For example, my lace was 3″ deep, so for each lace strip I subtracted 1-1/2″ from the curtain fabric’s cutting length. (I used four strips: 4 x 1-1/2″ = 6″; therefore I subtracted 6″ from the length of my curtain to make room for the lace.)

Step 3) Cut the fabric pieces.

For each fabric strip, cut a strip with a 3/4″-wide allowance along each edge that will be adjoined to a lace strip. For example, if I wanted a 6″-deep finished fabric strip with lace on each long edge, I would cut it to be 7-1/2″ deep. (6″ + 3/4″ + 3/4″ = 7-1/2″)

Step 4) Finish the fabric edges.

Along each fabric edge that will be joined to a lace strip, turn under 1/4″ and press in place. Repeat to hide the raw edge.

Curtain with Lace Inserts - step 1

Topstitch each folded fabric edge in place along the inside folded edge.

Curtain with Lace Inserts - step 2

Repeat to finish the lace-adjoining edges of each fabric strip.

Curtain with Lace Inserts - step 5

Step 5) Join the fabric and lace strips.

Place a lace strip over the right side of the curtain, overlapping the edges about 3/16″ (a scant 1/4″).

Curtain with Lace Inserts - step 3

Edgestitch the lace strip in place along the edges.

Curtain with Lace Inserts - step 4

 Repeat to continue adding fabric and lace strips.

Curtain with Lace Inserts - step 6

Curtain with Lace Inserts - step 7

Curtain with Lace Inserts - step 8

Step 6) Finish the curtain sides.

Turn under each long side of the curtain 1/2″ and press. Repeat to hide the raw edges, and then topstitch them in place.

Curtain with Lace Inserts - step 9

Step 7) Make the rod casing.

Turn under the curtain top edge 1/2″ and press in place. Turn it under again 2″ and press. Topstitch along the casing’s bottom edge to secure. Do not sew the sides closed.

Curtain with Lace Inserts - step 10

Step 8) Sew the hem.

Turn under the hem 1/2″ and press in place. Turn it under again, 4″ this time, and press in place. Topstitch along the hem’s top edge and sides to secure.

Curtain with Lace Inserts - step 11

Curtain with Lace Inserts

Curtain with Lace Inserts


January 30, 2014 by Nicole Smith
UA:F [1.9.22_1171]
Rating: 2.5/5 (24 votes cast)
Rate this post:

This article has no comments

Leave a Reply