How to Make a Sheer Summer Top

Light and flowing like a summer breeze, this sheer top adds a touch of cool elegance when the weather gets hot. Casual enough for beachwear, yet stylish enough for an evening on the town, it’s an easy pick for a beautiful summer day.

DIY Sheer Summer Top

Supplies

  • 2-5/8 yards of sheer fabric
  • 8 yards of lace trim, 1/2″ to 3/4″ wide
  • 2-1/2 yards of 1/4″-wide double-sided satin ribbon
  • OESD LightWeight Tear-Away stabilizer
  • Construction thread
  • Temporary fabric marker
  • Scissors
  • Ruler
  • Edgestitch foot (BERNINA Edgestitch Foot #10/10C/10D)

Step 1) Create the neck opening pattern.

Measure your natural neckline from your center front to your shoulder and determine how wide you want the neck opening to be.

measure your neckline

Make your neck opening pattern:

  • Fold a piece of paper in half twice as shown.

fold paper in quarters

  • Make the pattern as wide as determined above.
  • Make the pattern 1-1/2″ deep at the center front, tapering to a soft corner at the opposite side.
  • Add a 1/4″-wide seam allowance inside the drawn line.

make the neckline pattern piece

Cut out your neck opening pattern piece.

neck pattern piece

Step 2) Cut the fabric and finish the neckline.

Cut a rectangle of sheer fabric 92″ long and 50″ wide.

Center the neck opening pattern piece on the fabric, parallel to the short (50″-long) ends.

neckline pattern pinned to fabric

Cut out the neck opening using the pattern as a guide.

Sew along the neckline using a 1/4″-wide seam allowance.

stitch around neckline at 1/4"

Tip: Does sewing on sheer fabric make you nervous? Try installing a single-needle-hole throat plate (a.k.a. straight stitch plate) on your machine. The tiny needle opening helps prevent the fabric from being pushed under the stitch plate as you sew.

BERNINA Straight Stitch Plate

Turn the raw edge under along the stitching line; press.

Edgestitch close to the fold to secure the edge in place.

fold under along stitching

Trim away the raw edge close to the stitching.

trim away excess fabric

Turn the edge under along the stitching; press.

Edgestitch close to the inner fold to secure the edge of the hem in place.

Step 3) Add the buttonholes and casing.

Draw two 1/2″-wide vertical buttonholes 10″ from one 50″-wide edge of the rectangle. (This will be the top’s front.) Space them about 1″ apart.

Cut a piece of tear-away stabilizer and place it behind the marked buttonholes on the fabric’s wrong side.

mark the buttonholes

Stitch buttonholes along the marked lines. (For instructions, see your sewing machine manual.)

buttonholes in sheer fabric

Gently tear away the stabilizer from the wrong side of the buttonholes. Be careful not to rip the fabric.

remove stabilizer

Cut two 23″-long and 2″-wide strips of fabric.

Turn each short end under 1/4″ two times; stitch to secure.

hemmed casing end

Turn both long edges of one strip under 1/2″.

Center this strip over the buttonholes with the long edges parallel to the top’s 50″-long edge. Pin in place.

pin casing in place

Edgestitch the strip in place along both long edges.

Repeat for the remaining strip, stitching it to the back of the top, 10″ from the opposite 50″-long edge.

edgestitch casing strip in place

Step 4) Hem the edges.

Stitch around the raw edges of the rectangle using a 1/2″-wide seam allowance.

staystitch the edges

Turn the edges toward the right side; press.

Stitch close to the folded edge.

stitch close to folded edge

Trim the raw edge close to the stitching.

Pin the lace around the edges of the top, on the top’s right side. Make sure the lace hides the fabric’s raw edge.

Edgestitch the lace in place.

stitch lace to edge

Step 5) Insert the ribbon and adjust the fit.

Thread the ribbon through one buttonhole and into the casing on the top’s left side.

thread ribbon into casing

Thread the ribbon into the casing on the back of the top.

thread ribbon into casing

Thread the ribbon back into the casing on the front of the top, then out through the second buttonhole.

thread ribbon into casing

Put on your new top, adjust the ribbon to fit, tie the ends in a box, and then trim away the excess ribbon.

DIY Sheer Summer Top

One thought on “How to Make a Sheer Summer Top

Leave a Reply